中兴e8820s刷机 |
您所在的位置：网站首页 › e8820v2 刷固件 › 中兴e8820s刷机 |
中兴e8820s刷机
|
本帖最后由 sivs147 于 2020-5-17 16:48 编辑 2020/05/17 最新板OPEWNRT官方源碼，核心更新為5.4版，因此，文件有改重新修正， 目前交換晶片改DSA驅動，所以SWconfig的VLAN控制方式，不能再用了 有用到VLAN需安裝ip-bridge.apk 設定檔建議不要保留，採用全新設定，不然會出現怪問題 1.資料夾結構有小改，需要注意 2.UI有兩種預設是原OPENWRT風格、2020風格 3.OPENWRT r13243下載網址链接：https://share.weiyun.com/32425FJv 密码：7pwhze 以下版本適用OPENWRT 19.02之後的版本，核心改5.4 須修改兩個檔案，新增一個檔案 ./target/linux/ramips/mt7621/base-files/etc/board.d/01_leds(須修改) ./target/linux/ramips/image/mt7621.mk(須修改)./target/linux/ramips/dts/mt7621_zte_e8820v2.dts(新增) 1. ./target/linux/ramips/mt7621/base-files/etc/board.d/01_leds 新增 ======================================================================================= zte,e8820v2) ucidef_set_led_netdev"sys" "SYS_LED" "$boardname:white:sys""eth0" "tx rx" ucidef_set_led_default"power" "POWER_LED" "$boardname:white:power""1" ;; ====================================================================================== 2. ./target/linux/ramips/image/mt7621.mk 新增 ======================================================================================= define Device/zte_e8820v2 IMAGE_SIZE := 16064k DEVICE_VENDOR := ZTE DEVICE_MODEL := E8820V2 DEVICE_PACKAGES := \ kmod-mt7603 kmod-mt76x2 kmod-usb3 kmod-usb-ledtrig-usbport wpad luci endef TARGET_DEVICES += zte_e8820v2 ======================================================================================= 3. ./target/linux/ramips/dts/mt7621_zte_e8820v2.dts 新增 ======================================================================================= /dts-v1/; #include "mt7621.dtsi" #include #include / { compatible = "zte,e8820v2", "mediatek,mt7621-soc"; model = "ZTE E8820V2"; aliases { led-boot = &led_sys; led-failsafe = &led_sys; led-running = &led_sys; led-upgrade = &led_sys; }; chosen { bootargs = "console=ttyS0,115200"; }; leds { compatible = "gpio-leds"; led_sys:sys { label = "e8820v2:white:sys"; gpios = ; }; led_power:power { label = "e8820v2:white:power"; gpios = ; }; }; keys { compatible = "gpio-keys"; reset { label = "reset"; gpios = ; linux,code = ; }; wps { label = "wps"; gpios = ; linux,code = ; }; }; }; &spi0 { status = "okay"; m25p80@0 { compatible = "jedec,spi-nor"; reg = ; spi-max-frequency = ; partitions { compatible = "fixed-partitions"; #address-cells = ; #size-cells = ; partition@0 { label = "u-boot"; reg = ; read-only; }; partition@30000 { label = "u-boot-env"; reg = ; read-only; }; factory: partition@40000 { label = "factory"; reg = ; read-only; }; partition@50000 { compatible = "denx,uimage"; label = "firmware"; reg = ; }; }; }; }; &pcie { status = "okay"; }; &pcie0 { mt76@0,0 { reg = ; mediatek,mtd-eeprom = ; led { led-active-low; }; }; }; &pcie1 { mt76@0,0 { reg = ; mediatek,mtd-eeprom = ; ieee80211-freq-limit = ; led { led-sources = ; led-active-low; }; }; }; &gmac0 { mtd-mac-address = ; }; &switch0 { ports { port@4 { status = "okay"; label = "wan"; mtd-mac-address = ; }; port@0 { status = "okay"; label = "lan1"; }; port@1 { status = "okay"; label = "lan2"; }; port@2 { status = "okay"; label = "lan3"; }; port@3 { status = "okay"; label = "lan4"; }; }; }; &state_default { gpio { groups = "i2c", "uart2", "uart3", "wdt"; function = "gpio"; }; }; ======================================================================================= 以下版本適用OPENWRT 19.07 須修改三個檔案，新增一個檔案 ./target/linux/ramips/mt7621/base-files/etc/board.d/01_leds(路徑有修改) ./target/linux/ramips/mt7621/base-files/etc/board.d/02_network(路徑有修改) ./target/linux/ramips/image/mt7621.mk(須修改) ./target/linux/ramips/dts/mt7621_zte_e8820v2.dts(新增) 1. ./target/linux/ramips/mt7621/base-files/etc/board.d/01_leds 新增 ======================================================================================= zte,e8820v2) ucidef_set_led_netdev"sys" "SYS_LED" "$boardname:white:sys""eth0" "tx rx" ucidef_set_led_default"power" "POWER_LED" "$boardname:white:power""1" ;; ====================================================================================== 2. ./target/linux/ramips/mt7621/base-files/etc/board.d/02_network 新增 ======================================================================================= zte,e8820v2) ucidef_set_interfaces_lan_wan"eth0.1" "eth0.2" ucidef_add_switch"switch0" "1" "1" \ "0:lan:1""1:lan:1" "2:lan:1" "3:lan:1" "4:wan:2""6t@eth0" ;; ======================================================================================= 3. ./target/linux/ramips/image/mt7621.mk 新增 ======================================================================================= define Device/zte_e8820v2 MTK_SOC := mt7621 IMAGE_SIZE := 16064k DEVICE_VENDOR := ZTE DEVICE_MODEL := E8820V2 DEVICE_VARIANT := 16M DEVICE_PACKAGES := \ kmod-mt7603 kmod-mt76x2 kmod-usb3 kmod-usb-ledtrig-usbport wpad hostapd-utils luci endef TARGET_DEVICES += zte_e8820v2 ======================================================================================= 4. ./target/linux/ramips/dts/mt7621_zte_e8820v2.dts 新增 ======================================================================================= /dts-v1/; #include "mt7621.dtsi" #include #include / { compatible = "zte,e8820v2", "mediatek,mt7621-soc"; model = "ZTE E8820V2"; aliases { led-boot = &led_sys; led-failsafe = &led_sys; led-running = &led_sys; led-upgrade = &led_sys; }; chosen { bootargs = "console=ttyS0,115200"; }; leds { compatible = "gpio-leds"; led_sys:sys { label = "e8820v2:white:sys"; gpios = ; }; led_power:power { label = "e8820v2:white:power"; gpios = ; }; }; keys { compatible = "gpio-keys-polled"; poll-interval = ; reset { label = "reset"; gpios = ; linux,code = ; }; wps { label = "wps"; gpios = ; linux,code = ; }; }; }; &spi0 { status = "okay"; m25p80@0 { compatible = "jedec,spi-nor"; reg = ; spi-max-frequency = ; partitions { compatible = "fixed-partitions"; #address-cells = ; #size-cells = ; partition@0 { label = "u-boot"; reg = ; read-only; }; partition@30000 { label = "u-boot-env"; reg = ; read-only; }; factory: partition@40000 { label = "factory"; reg = ; read-only; }; partition@50000 { compatible = "denx,uimage"; label = "firmware"; reg = ; }; }; }; }; &pcie { status = "okay"; }; &pcie0 { mt76@0,0 { reg = ; mediatek,mtd-eeprom = ; led { led-active-low; }; }; }; &pcie1 { mt76@0,0 { reg = ; mediatek,mtd-eeprom = ; ieee80211-freq-limit = ; led { led-sources = ; led-active-low; }; }; }; ðernet { mtd-mac-address = ; }; &pinctrl { state_default: pinctrl0 { gpio { ralink,group = "i2c", "uart2", "uart3", "wdt"; ralink,function = "gpio"; }; }; }; ============================================================================ 以下版本僅適用於OPENWRT 18.06版 注意：更新完自動重開第一次無線都會無法載入，原因不明還再查找，但是確定移除電源重開就能載入 原廠EEPROM，不是每一台都一樣，建議最好備份自己機子的，如果沒有再考慮刷我的 https://share.weiyun.com/5clgMrS 密碼：ysvsyq 進入BREED刷完後，記得到MAC修改的位置紅色的部分填上原本的MAC 未命名.png (42.73 KB, 下载次数: 9) 2019-3-24 10:52 上传 如何編譯固件很多大神都有教學，我就提示要改哪些文件就好 如果有人能幫我上傳到GITHUB最好，因為我還搞不懂那個用法 編譯E8820V2須修改新增的檔案 共計五個如下 修改內容 ./target/linux/ramips/base-files/etc/board.d/01_leds ./target/linux/ramips/base-files/etc/board.d/02_network ./target/linux/ramips/image/mt7621.mk ./target/linux/ramips/base-files/lib/ramips.sh 新增檔案 ./target/linux/ramips/dts/E8820V2.dts 1. ./target/linux/ramips/base-files/etc/board.d/01_leds 新增 ======================================================================================= zte,e8820v2) ucidef_set_led_netdev"sys""SYS_LED" "$boardname:white:sys""eth0" "txrx" ucidef_set_led_default"power""POWER_LED" "$boardname:white:power""1" ;; ======================================================================================= 3. ./target/linux/ramips/base-files/etc/board.d/02_network 新增 ======================================================================================= zte,e8820v2) ucidef_set_interfaces_lan_wan"eth0.1""eth0.2" ucidef_add_switch"switch0""1" "1" \ "3:lan:1""2:lan:1""1:lan:1" "0:lan:1" "4:wan:2""6t@eth0" ;; ======================================================================================= 4. ./target/linux/ramips/image/mt7621.mk 新增 ======================================================================================= define Device/zte_e8820v2 DTS := E8820V2 IMAGE_SIZE :=$(ralink_default_fw_size_16M) DEVICE_TITLE := ZTE E8820V2 DEVICE_PACKAGES := \ kmod-mt76 kmod-mt7603 kmod-mt76x2 kmod-usb3kmod-usb-ledtrig-usbport wpad hostapd-utils endef TARGET_DEVICES += zte_e8820v2 ======================================================================================= 5. ./target/linux/ramips/base-files/lib/ramips.sh 新增 ======================================================================================= *"zte,e8820v2") name="e8820v2" ;; ======================================================================================= 6. ./target/linux/ramips/dts/E8820V2.dts 新增 ======================================================================================= /dts-v1/; #include "mt7621.dtsi" #include #include / { compatible ="zte,e8820v2","mediatek,mt7621-soc"; model ="ZTE E8820V2"; aliases { led-boot= &led_sys; led-failsafe= &led_sys; led-running= &led_sys; led-upgrade= &led_sys; }; memory@0 { device_type= "memory"; reg= ; }; chosen { bootargs= "console=ttyS0,115200"; }; leds { compatible= "gpio-leds"; led_sys:sys{ label= "e8820v2:white:sys"; gpios= ; }; led_power:power{ label= "e8820v2:white:power"; gpios= ; }; }; keys { compatible= "gpio-keys-polled"; poll-interval= ; reset{ label= "reset"; gpios= ; linux,code= ; }; wps{ label= "wps"; gpios= ; linux,code= ; }; }; }; &spi0 { status ="okay"; m25p80@0 { compatible= "jedec,spi-nor"; reg= ; spi-max-frequency= ; partitions{ compatible= "fixed-partitions"; #address-cells= ; #size-cells= ; partition@0{ label="u-boot"; reg=; read-only; }; partition@30000{ label="u-boot-env"; reg=; read-only; }; factory:partition@40000 { label="factory"; reg=; read-only; }; partition@50000 { compatible= "denx,uimage"; label="firmware"; reg=; }; }; }; }; &pcie { status ="okay"; }; &pcie0 { mt76@0,0 { reg= ; mediatek,mtd-eeprom= ; led{ led-active-low; }; }; }; &pcie1 { mt76@0,0 { reg= ; mediatek,mtd-eeprom= ; ieee80211-freq-limit= ; led{ led-sources= ; led-active-low; }; }; }; ðernet { mtd-mac-address= ; }; &pinctrl { state_default:pinctrl0 { gpio{ ralink,group= "i2c", "uart2", "uart3","wdt"; ralink,function= "gpio"; }; }; }; ======================================================================================= 如果可以建議用編程器複製出來再改刷，我測了四台都會有些微不同 第一台不知道在測試的時候發生什麼事，5G永遠都抓不到了 有注意到在進入Breed的時候，溫度會比在OP時候高，沒要刷別停著 不知道是不是停太久，燒掉了 修改符合OPENWRT如附圖 原廠==>新EEPROM 7603 0x2F000~0x2F12F==>0x0~0x7FFF 空的填FF MT7603位址.png (72.43 KB, 下载次数: 8) 2019-3-22 09:38 上传 7612 0x2F800~0x2F9EF==>0x8000~0x81EF 空的填FF MT7612位址.png (77.03 KB, 下载次数: 8) 2019-3-22 09:21 上传 有線MAC 0xE000開始填，E8820V2跟無線2.4G一樣，但是我看了WR1200JS的是前面填2.4GMAC，後面填有線MAC 舊版下載 由 https://pan.baidu.com/s/1f-8Jd8HNrpwT92MX2Z9c3A 提取碼: fz5d 裡面有breed也有樓主的固件，還有原版固件，但從breed刷不進去的 2020/02/11 花了點時間把802.11v和802.11k的網頁版改上去 已經有辦法改動/etc/config/wireless，但是用WIFI分析儀還是看不到 先放上來讓大家試試看，是不是我硬體的問題 鏈接：https://share.weiyun.com/5eCaBAt 密碼：94f3ju R9.12.3 鏈接：https://share.weiyun.com/5p1Ip40 密碼：c2qdvx r11684 鏈接：https://share.weiyun.com/5ZCjoeU 密碼：ifn6j7 |
【本文地址】
今日新闻 |
推荐新闻 |